Sunday, November 11, 2007

Floats repositioned for hull lamination.

I realized that the hulls should laminated before the decks so it was suddenly time to rearrange the floats in the garage. One float needs to hoisted up close to the garage ceiling and the other needs to be presented on its side. Like other builders I'm using form frames 5 and 9 to hold a float in this position.
To get the form frames into position one float had to take a break outside for an hour or so. Here is a shot of the float from above.
And from the side.
And with the new form frames in place, here is the new orientation.

This was also a good chance to give the garage a good sweep and clean up.

Saturday, November 10, 2007

Further comments on the 'plastic on peel ply' technique

I've covered the other bow cap now using this technique and I am noticing in some areas the plastic lifts during curing. The resulting laminate in these areas is dry. It is curious because I am sure I have the cloth and peel ply well saturated. I suspect these are areas where I have been too aggressive with pressure on the plastic. It is a powerful technique and overall I am extremely happy with the results. Wonderful adhesion with zero air bubbles. Just a few areas that I believe I can re wet out.

I am now moving on to the larger job of laminating the decks.

Thursday, November 08, 2007

Results of plastic on peel ply


Here is the bow cap with the plastic and peel ply off. The 2 layers of my B spec. 9 oz s-glass fiberglass cloth cannot really be seen. Only the little goatee at the keel bow curve indicates the presence of the cloth. I am actually very impressed. I will carry on with this technique. The addition of the plastic and the extra squeezing appears to really enhance the laminate quality.

The Mas epoxy seems to work OK. Curing time is shorter compared to the Aeropoxy resin and it is very clear. They advertise Mas as a good moisture barrier, which is why it is going on the outside. The Aeropoxy resin has amazing high temperature and mechanical properties which is why I have used it on the interior and structural parts of the floats.

I've been making extra efforts these days to do a little bit every day on the floats in the garage. So far a wee bit of heat from the infra red heaters is all I need. Last year I could work outside till Christmas time. I hope the weather this year is similar. I dearly want to get the outside of the floats laminated and start thinking about the main hull.

Wednesday, November 07, 2007

Plastic on Peel Ply

Final check on the bow cap shape. The picture shows how tightly the final shape fit the template cut into plywood.

As far as the fairing and shaping goes it got to the point where I just said - enough! So I cut the cloth, peel ply and this time a 'heavy' plastic sheet from home depot.


A comment that Biol made on Jay's site led me to investigate a technique called 'poor mans vacuum bagging'. This really just consists of applying a plastic sheet over the peel ply and using the seal to push air bubbles and excess resin out of the area with a plastic squeegee. I started a discussion on this on the F22 builders group site.


Here is my first attempt. There is a shiny clear plastic sheet over the black peel ply. In application it was not such a revelation. The plastic sheet does help to hold the laminate to the foam. However, the application of the two layers of my b spec. s-glass cloth applied so smooth and bubble free that I am not sure if the plastic really is doing much. There was one area where I did note excess resin getting worked out.

I also complicated the experiment by using a different resin. Now that I am laminating the outside of these parts I used a resin that

  1. Advertises good moisture resistance.
  2. Was on sale at Noah's.
The epoxy is MAS low viscosity resin with the slow hardener.

First complaint. The resin and hardener are the same colour. It is not so easy to tell when it is fully mixed. If anyone has any comments or experience with this resin. Comment away please.

My work place has moved and it happens (life is strange) that I am now about a 3 minute drive to Noah's Toronto main warehouse. Very handy indeed for quick lunch break supply runs.

U-Spar estimate on the F22 carbon fiber mast

I received a response from U-Spar at http://u-spar.com/ regarding my
inquiry for a carbon fiber mast for the F-22. They do not have a

section small enough for the F-22 although they would consider making
a mold for an order for 3 or more masts. They state that "Our masts
are made with alternating layers of uni-directional pre-preg,
typically with 65 - 75% of the fibres in the 0 axis, and the remainder
at + & - 45 deg. This combination gives by far the highest
longitudinal stiffiness to weight ratio, combined with high torsional
strength. Point-load areas, such as tangs, winch pads etc., and cut-
outs for halyard exits etc. are all substantially reinforced." But
they admit for a small mast they are probably not price competitive.
They estimate the price for a complete mast, including the rotator
cup, painted and ready to go, would be in the region of $8,750 Cdn,
with a 10% discount for 3 or more masts.

Saturday, November 03, 2007

Full Monty on the bow shapes


I'm sure I've related in earlier blogs that I have seen issues in the resulting bow sections after I joined the float halves. I addressed some of this as best I could earlier with light filler, as seen above, but it is time to pay the piper when your trying to get the bow caps shaped correctly. Root cause of the problem? I suspect there was an issue in how I laid up the foam in the frames and/or the halves twisted in storage outside.

So, how do I know I am shaping the cap correctly? Well first I used the two beam locating dowels to verify that the bow cap radius is dead ahead. Then I used a plumb bob to verify the position of the keel - bow radius. Then I used a straight edge to fair the bow cap to the shape of the float hull. This is where the use of filler comes in.



I ended up fairing the keel bow thickness down to something close to 3/8" thickness. This could be a bit sharp. At deck level the thickness at the bow is ~ 1 3/8".


Gunwales are close to finished. I found the use of the rigid long board helpful here. You can also see that my access hatches have arrived. I am actually pretty close to covering the bow caps, transoms and decks with the A spec. fiberglass. Yup, time to get the heaters out again.


Putty and cloth around the chain plates. I apply the cloth when the putty is still wet. Actually I saturate the cloth with the putty before applying it against the wet putty build. I'll clean it up when it's hard and cured.

Google group for F22 builders

I've created a google group for F22 builders.

I want to get this blog back on focus as a personal build diary. The group site can be the place where questions and discussions amongst the builder community can take place.

I've made the core group of the F22 build bloggers managers of this site so that there should be no delays associated with approvals and other administrative activities. I'm listed as the owner (I am the creator - sorry a joke from work) but the site belongs to all of us. If it works for everyone - fantastic. If it doesn't, well, as a wise man once said, 'not every effort can be a cracker-jack'.